mcsysinforeport

mcsysinforeport
Prev	Data Formats Reference	Next

Name

mcsysinforeport — MagniComp™ SysInfo™ report output format

Synopsis

mcsysinfo --repsep '|' --format report

DESCRIPTION

This document describes the report output format from MagniComp's mcsysinfo(1) command. This format is output when the --format report option is specified to SysInfo. The format of this output is intended to be most easily parsed by software, not humans.

The report format consists of multiple fields each seperated by the | (vertical pipe) character. Other field delimiters may be specified using the --repsep option.

Each entry is terminated by a newline. Each field may optionally begin and/or end with white-space (any combination of <SPACE> and/or <TAB> characters). An empty field consists of no characters or only white-space appearing between field seperators. The content of a used field may consist of any printable ASCII character set including, but not limited to:

a-z A-Z 0-9 <SPACE> <TAB> ...

The first field specifies the class of information being provided. Each class uses the remaining fields in the same general, but varying manner as follows:

Table 1. Overview of Output

Field # Content Description

Class

This field names the class of information being provided. Values correspond explicitly to --class arguments. Valid values are:

`device`	Device (hardware) configuration information.
`filesys`	Mounted filesystem information.
`general`	General information about system.
`kernel`	Kernel configuration information.
`netif`	Network interface information.
`network`	Network information.
`partition`	Filesystem and disk partition configuration information.
`printer`	All printer queues defined on the system both local and remote.
`siteinfo`	Site defined information.
`software`	Software which is installed and registered with the OS.
`sysconf`	System configuration information.

1 Sub-Class This field may be empty or may contain a keyword which specifies a context specific to the Class. Common values are: name, prop, and desc. Valid Sub-Class values are defined for each Class later in this document.

2 Variable Specifies the name of a variable which the remaining fields describe.

3 Value Specifies a value of some type.

4 ... The remaining fields vary in number and content based upon the Field 0 - Class value.

Class device

The Device class provides detailed information about physical hardware installed in a system.

There are multiple forms of a device entry. Each form is specified by the Field 1 Sub-Class field. Each form is described in it's entirety below:

Table 2. Format of device Information

Field #	Keyword	Description	Example
0	`device`	The word `device` specifies the usage described in this section.	`device`
1	`name`	The canonical definetion of a device.	`name`
2	`Name`	Specifies the name of this device.	`c0t0d0`
3	`Alt Name`	A alternative name by which this device is known.	`sd0`
4	`Master Name`	The name of this device's master.	`ctlr0`
5	`File List`	A comma seperated list of filenames associated with this device.	`/dev/dsk/c0t0d0s0,/dev/dsk/c0t0d0s2`
6	`Type Name`	A name describing the type of device. Each name corresponds to DT_* and DTN_* values in `mcsysinfo.h.`	`diskdrive`
7	`Type Description`	A more verbose description of the type of device.	`Disk Drive`
8	`Model`	A short description specifying the device's model.	`ST123456`
9	`Model Description`	A more descriptive version of the device model.	`ATA`
10	`Unit`	The device's unit number.	`0`
11	`Address`	Obsolete.
12	`Prio`	Obsolete.
13	`Vec`	Obsolete.
14	`Node ID`	The device's unique node ID relative to the OS.	`0x12345`
15	`Class Name`	A name describing the classification of this device relative to it's Type. These values correspond to CT_* definetions in `mcsysinfo.h.`	`SCSI`
16	`Class Description`	A more verbose description of the device's class.
17	`Vendor`	The name of the device's vendor.	`Seagate`
18	`Serial #`	The device's serial number.	`A1234543`
19	`Revision`	The revision of the device.	`A01`
20	`Identifier`	The device's identifier.
21	`Part #`	The part number of the device as assigned by the manufacturer.	`X1234A`
22	`Next Name`	The name of the next device (relative to the parent) of the device hierarchy tree.	`c0t1d0`
23	`Child Names`	The comma seperated list of slave (children) device node names of the device hierarchy.
24	`Capacity`	The capacity (size) of the device in device specific units.	`64 GB`
25	`Speed`	The speed of the device in device specific units.	`320 MB/s`
26	`Bus`	The bus number the device is attached to.	`0`
27	`DevNum`	The device number which identifies the device.	`0`
28	`Port`	The port number the device is connected to on the bus.	`0`

Device CpuInfo Information

Detailed information about a CPU is indicated when field 0 is set to the word device and field 1 is set to the word cpuinfo. The following table describes the meaning of each field:

Table 3. Format of cpuinfo Information

Field #	Keyword	Description	Example
0	`device`	The word `device` specifies the usage described in this section.	`device`
1	`cpuinfo`	The word `cpuinfo` further specifies the usage described in this section.	`cpuinfo`
2	`Name`	Specifies the device name for this entry.	`sd0`
3	`Man`	The name of the manufacturer of this CPU.	`Intel`
4	`Model`	The model of CPU.	`Pentium-4`
5	`Arch`	The architecture of the CPU.	`i686`
6	`ArchVer`	The version of the CPU's architecture.	`IA32`
7	`Serial`	The serial number of the CPU.	`ABC123456`
8	`BitSize`	The bitsize of the CPU.	`32`
9	`Speed`	The clock speed of the CPU.	`1.1 GHz`
10-25		These fields are obsolete.
26	`Has FPU`	Value of `1` if a Floating Point Unit (FPU) is present.	`1`
27	`Stepping`	The CPU's stepping value.	`30`

Device CacheInfo Information

Detailed information about a CPU is indicated when field 0 is set to the word device and field 1 is set to the word cacheinfo. The following describes the meaning of each field:

Table 4. Format of cacheinfo Information

Field # Keyword Description Example

0 device The word device specifies the usage described in this section. device

1 cacheinfo The word cacheinfo further specifies the usage described in this section. cacheinfo

2 Name Specifies the name of the processor device to which this cache is associated. cpu0

3 CacheName Specifies the name of the cache which is unique to the device. L1 Inst

4 Size The size of the cache. 64 KB

5 Associativety The associativety of the cache. 2

6 Lines The number of lines of the cache. 1

7 Line Size The size of each cache line. 64

8 TLB The CPU's instruction TLB. 32

9 TLB Associativety The CPU's instruction TLB associativety. 32

10 Enabled If this field is set to 1 the cache is present and enabled. If set to 0 the cache is present, but not enabled. If the field is unset the state is unknown. 1

Type

The type of cache:

`1`	Instruction
`2`	Data
`3`	Unified

2

12 Level The level of cache. 1

13 Speed The speed of the cache in nano-seconds. 200

14 Socketed If set to 1 the cache is socketed to the CPU. If set to 0 the cache is not socketed. If unset, the state is unknown. 0

15 Location The location of the cache. onboard

16 SramType The type of SRAM present. Pipeline Burst

17 EccType The type of Error Correction used. Parity

18 Mode The mode of operation of the cache. Write Back

Device Description Information

Unclassified information about a device is provided in the form of a description and it's value. The content of each field is free form text and varies from OS to OS. It should not be relied upon for consistency. The fields are defined as follows:

Table 5. Format of Device Description Information

Field #	Keyword	Description	Example
0	`device`	The word `device` specifies the usage described in this section.	`device`
1	`desc`	This entry provides additional, unclassified descriptive information about this entry.	`desc`
2	Name	Specifies the name of this entry.	`vendorPart`
3	Description	The description of the entry.	`Vendor Specific Part Number`
4	Value	The value of the description.	`X1234A`

Device NetIf Information

Detailed information about a Network InterFace associated with a device is indicated when field 0 is set to the word device and field 1 is set to the word desc and field 3 is set to the word internet. This type of entry contains a subset of information available from the NetIf (network interface) class.

The following describes the meaning of each field:

Table 6. Format of Device Network Interface Information

Field #	Keyword	Description	Example
0	`device`	The word `device` specifies the usage described in this section.	`device`
1	`desc`	The word `desc` specifies the usage described in this section.	`desc`
2	`If`	The system name of the network interface.	`eth0`
3	`internet`	The word `internet` specifies the type of address being described.	`internet`
4	`HostAddr`	The host address (usually IP) of the interface.	`10.1.2.3`
5	`HostName`	The host name of the interface.	`fritz`
6	`NetAddr`	The network address (usually IP) of the interface.	`10.1.0.0`
7	`NetName`	The network name of the interface.	`corpnet`
8	`MACaddr`	The current MAC address of the interface.	`0:8:20:a:b:c`
9	`MACname`	The current MAC address name of the interface.	`fritz-eth0`
10	`FacMACaddr`	The factory MAC address of the interface.	`0:8:20:a:b:c`
11	`FacMACname`	The factory MAC address name of the interface.	`fritz-eth0`
12	`NetMask`	The network mask for this address in quaded dot format.	`255.255.0.0`
13	`Broadcast`	The network broadcast address for this interface.	`255.255.255.255`

Class filesys

Detailed information about currently mounted filesystems (or any mount entry) is provided when field 0 is set to the word filesys.

Each new block of filesystem information begins with a name entry as follows:

Table 7. Format of filesys Name Entry

Field #	Keyword	Description	Example
0	`filesys`	The word `filesys` specifies the usage described in this section.	`filesys`
1	`name`	The word `name` specifies the usage described in this section.	`name`
2	`Name`	The name of the filesystem about to be described.	`/tmp`

Property information about each filesystem is presented as one property item per entry (line). The following format is used:

Table 8. Format of filesys prop Entry

Field # Keyword Description Example

0 filesys The word filesys specifies the usage described in this section. filesys

1 prop The word prop specifies the usage described in this section. prop

2 Name The name of the filesystem about to be described. /tmp

Keyword

This field contains a fixed set of keywords as follows:

`MntName`	Name (path) of mount location. i.e. `/var`
`DevPath`	The location (source) of the mount point. This is usually a device name for a local filesystem or the path name on the server if this is an nfs mount. `/dev/dsk/c0t0d0s3` or `/vol/vol0`
`DevPathRaw`	The raw device path. For local filesystems, this is the raw device path. `/dev/rdsk/c0t0d0s3`
`DevName`	The name of the device on which this filesystem resides.
`Server`	The server (if any) from which this filesystem is mounted from.
`Type`	The type of filesystem. i.e. nfs ext3 ufs etc.
`Opts`	The primary mount option. i.e. rw or ro
`MntOpts`	A comma seperated list of mount options.
`Size`	The total size (in Mbytes) of the filesystem.
`AmtUsed`	The amount of space used (in Mbytes) on the filesystem.
`AmtAvail`	The amount of space available (in Mbytes) on the filesystem.

4 Description A description of this entry type. Mount Location

5 Data The actually data (value) for this entry. ufs

Class general

When Field 0 is set to general, the following describes the usage of each field:

Table 9. Format of general Information

Field #	Keyword	Description	Example
0	`general`	The word `general` specifies the usage described in this section.	`general`
1	unused	This field is unused.
2	`Keyword`	A fixed name keyword used to uniquely identify this type of data. The keywords matches the valid values for `--show``variable.`	`osname`
3	`Description`	Descriptive text of what this entry contains.	`OS Name`
4	`Value`	The value of this entry.	`Solaris`

Class kernel

When Field 0 is set to kernel, the following describes the usage of each field:

Table 10. Format of kernel Information

Field #	Keyword	Description	Example
0	`kernel`	The word `kernel` specifies the usage described in this section.	`kernel`
1	unused	This field is unused.
2	`Variable`	Names the variable being described. The keywords matches the valid values for `--show``variable`.	`maxproc`
3	`Description`	Descriptive text of `Variable`.	`Maximum Processes`
4	`Value`	The value of this entry.	`500`

Class license

When Field 0 is set to license, information about software licenses is provided.

Each new block of license information begins with a name entry as follows:

Table 11. Format of license Name Entry

Field #	Keyword	Description	Example
0	`license`	The word `license` specifies the usage described in this section.	`license`
1	`name`	The word `name` specifies the usage described in this section.	`name`
2	`Name`	The name of the license about to be described.	`StarOffice`

Property information about each license is presented as one property item per entry (line). The following format is used:

Table 12. Format of license Property Information

Field # Keyword Description Example

0 license The word license specifies the usage described in this section. license

1 prop The word prop specifies the usage described in this section. prop

2 Name The name of the license this property applies to. StarOffice

Keyword

This field contains a fixed set of keywords as follows:

`softver`	Software version
`type`	Type of license. Valid values are: `float` (Floating/concurrent), `node` (Node locked to one system).
`typedesc`	A descriptive string describing this type.
`port`	The port the license server is running on.
`count`	The total number of possible licenses.
`file`	The path to the license file.
`serversoft`	The name of the license server software.
`serverver`	The version of the license server software.
`vendorserversoft`	The name of the vendor's auxiliary license server program.
`vendorserverversoft`	The version of the license server software.
`issuer`	The organization which issued the licensed.
`hostid`	The hostid(1) the license is tied to.
`issuedate`	The date the license was issued.
`startdate`	The date the license is usable.
`expiredate`	The date the license expires and becomes unusable.
`serial`	The license serial number/ID.
`key`	The license key.

4 Description The description for this property type. Software Version

5 Value The property value for this entry. 1.1

Class NetIf

Detailed information about a Network InterFace is provided when field 0 is set to the word netif.

Each new block of netif information begins with a name entry as follows:

Table 13. Format of netif Name Entry

Field #	Keyword	Description	Example
0	`netif`	The word `netif` specifies the usage described in this section.	`netif`
1	`name`	The word `name` specifies the usage described in this section.	`name`
2	`Name`	The name of the netif about to be described.	`eth0`

Property information about each netif is presented as one property item per entry (line). The following format is used:

Table 14. Format of netif Property Information

Field # Keyword Description Example

0 netif The word netif specifies the usage described in this section. netif

1 prop The word prop specifies the usage described in this section. prop

2 Name The name of the netif this property applies to. eth0

Keyword

This field contains a fixed set of keywords as follows:

`addrtype`	Type of address.
`iftype`	Type of interface. Possible values are: `physical` (An actual physical interface), `virtual` (A virtual (software) interface)
`hostaddr`	Host address (usually IP) of the interface.
`hostname`	Host name of the interface.
`netaddr`	Network address (usually IP) of the interface.
`netname`	Network name of the interface.
`macaddr`	Current MAC address of the interface.
`macname`	Current MAC address name of the interface.
`facmacaddr`	Factory MAC address of the interface.
`facmacname`	Factory MAC address name of the interface.
`mediatype`	The type of media. i.e. `ethernet`, `fddi`
`mediasubtype`	The sub type of media. i.e. `100-base-T`, `1000-base-TX`
`netmask`	Network mask for this address in quaded dot format.
`broadcast`	Network broadcast address for this interface.
`mtu`	The MTU Size.
`speed`	The current link speed.
`duplex`	The current link duplex, either `full` or `half`
`flag`	This is a special entry which lists one of the flags set for this interface. When this field (field 3) is set to `flag` the flag keyword is found in field 4 and the description of this flag is found in field 5.

4 Description The description for this property type. Address Type

5 Value The property value for this entry. Internet

Class Network

Detailed information about various network related parameters is provided when field 0 is set to the word network. The following format applies:

Table 15. Format of a network Entry

Field # Keyword Description Example

0 network The word network specifies the usage described in this section. network

1 Reserved This field is reserved for future use.

Keyword

This field contains a fixed set of keywords as follows:

`defgwip`	Default gateway IP address.
`defgwname`	Default gateway hostname.
`dnsdomain`	DNS domain name.
`dnsserverips`	DNS Server IP addresses (comma seperated).
`dnsservernames`	DNS Server hostnames (comma seperated).
`nisdomain`	NIS (formerly YP) domain name.
`nisservermethod`	The method by which a NIS server is selected. The value field will contain one of the following: `broadcast` (The system broadcasts for a server), `static` (One or more servers are statically defined).
`nisserverips`	The comma seperated list of IP addresses of NIS servers. Applies only when the `nisservermethod` is set to `static`.
`nisservernames`	The comma seperated list of hostnames of NIS servers. Applies only when the `nisservermethod` is set to `static`
`nisserver`	The name of the currently bound NIS server.
`nismaster`	The name of the master NIS server for this domain.

3 Description The description for this property type. DNS Domain

4 Value The property value for this entry. foo.com

Class partition

The Partition class provides information about disk partitions on a system. The format is as follows:

Table 16. Format of a partition Entry

Field #	Keyword	Description	Example
0	`partition`	The word `partition` specifies the usage described in this section.	`partition`
1	`name`	The word `name` specifies the usage described in this section.	`name`
2	`Device Path`	The full pathname of this entry's device.	`/dev/sda1`
3	`Device Name`	The name of this partition entry relative to the `Device Path`.	`sda1`
4	`Base Name`	The base filename of the Device Name or Path.	`sda1`
5	`Partition Number`	The numeric partition number relative to this `Device Name/Path`	`1`
6	`Raw Device Path`	The pathname of the raw device for this entry.	`/dev/rsda1`
7	`Type Name`	A short name describing the type of partition this is.	`EXTDOS`, `ufs`
8	`Type Description`	A more verbose description of the type of partition.	`Extended DOS`
9	`Type Number`	A numeric value representing the partition type.	`83`
10	`Usage Status`	Description of how this partition is being used.	`FILESYSTEM`, `SWAP`
11	`Mount Name`	If this partition contains a filesystem, then this field describes the mounted name of the partition.	`/export`
12	`Mount Options`	If this is a mounted filesystem, this field describes any options used to mount the filesystem.	`rw,quota`
13	`Size`	The total size of this partition in bytes.	`5010000`
14	`Amount Used`	The total amount of used space on this partition in bytes.	`201000`
15	`Sector Size`	The size of a single sector in bytes.	`512`
16	`Starting Sector`	The sector number this partition starts on.	`54`
17	`Ending Sector`	The sector number this partition ends on.	`10054`
18	`Number of Sectors`	The total number of sectors this partition uses.	`10000`

Class printer

The Printer class provides information about printer queues known to the local system. The format is as follows: There are multiple forms of printer entries. Each form is specified by the Field 1 Sub-Class field.

Table 17. Format of a printer name Entry

Field #	Keyword	Description	Example
0	`printer`	The word `printer` specifies the usage described in this section.	`printer`
1	`name`	The word `name` specifies the usage described in this section.	`name`
2	`Queue`	The canonical name of this printer queue.	`fastcolor1`
3	`Aliases`	A comma seperated list of aliases for this printer.	`bucket,bolts`
4	`Description`	A text description of this printer queue. The format is usually site dependent.	`Acme EZ100 Color Printer in room 101`
5	`Vendor`	The name of the vendor who manufactures or sells this printer.	`Acme`
6	`Model`	The model of printer.	`EZ100`
7	`Protocol`	The protocol used to connect to this printer. Valid names are: `local` (The printer is attached to a local device such as a serial or parallel port), `LPD` (The printer is on a remote server which uses the LPD protocol for communication), `SYSV` (The printer is on a remote server which uses the AT&T System V printer protocol), `SMB` (The printer is on a remote server which uses the Windows SMB printer protocol).
8	`Device`	The name or path of the local device, if any, on which the printer is attached.	`/dev/lp0`
9	`Server`	The name of the remote server, if any, which provides service for the printer.	`printsrv1`
10	`RemoteQueue`	The name of the remote queue on the remote Server	`fastcolor1`
11	`Languages`	A comma seperated list of printer languages which the printer supports.	`PS`
12	`SpoolDir`	The name of the local directory used for spooling print jobs for the printer queue.	`/var/spool/print/fastcolor1`
13	`MaxJobSize`	The maximum sized job accepted for the printer queue.	`500000`

Table 18. Format of a printer desc Entry

Field #	Keyword	Description	Example
0	`printer`	The word `printer` specifies the usage described in this section.	`printer`
1	`desc`	The word `desc` specifies the usage described in this section.	`desc`
2	`Name`	The name of the printer.	`fastcolor1`
3	`Description`	The description of the entry.	`Color Ink Type`
4	`Value`	The value of the description.	`messy`

Class siteinfo

The siteinfo class provides site defined information specific to each customer.

Each new block of site information begins with a name entry as follows:

Table 19. Format of siteinfo Name Entry

Field #	Keyword	Description	Example
0	`siteinfo`	The word `siteinfo` specifies the usage described in this section.	`siteinfo`
1	`name`	The word `name` specifies the usage described in this section.	`name`
2	`Variable`	The site info variable about to be described.	`Location`

Property information about each site info variable is presented as one property item per entry (line). The following format is used:

Table 20. Format of siteinfo prop Entry

Field #	Keyword	Description	Example
0	`siteinfo`	The word `siteinfo` specifies the usage described in this section.	`siteinfo`
1	`prop`	The word `prop` specifies the usage described in this section.	`prop`
2	`Variable`	The unique variable name identifying this property.	`Location`
3	`Key`	A predefined keyword which identifies the type of data. Valid values are: `Var` (Variable), `Desc` (Description), `Value` (Value).	`Var`
4	`Description`	A description of what the `Key` means.	`Variable`
5	`Value`	The property value.	`Room-101`

Class software

The Software class provides data about installed and registered software.

There are multiple format entries which are defined as follows:

Table 21. Canonical definetion of a software package

Field #	Keyword	Description	Example
0	`software`	The word `software` specifies the usage described in this section.	`software`
1	`name`	The word `name` specifies the usage described in this section.	`name`
2	`Name`	The canonical name of this software package or product.	`glib`
3	`Type`	The type of software entry being described. Values are: `pkg` (The entry is a software package, the lowest level component) `product` (The entry represents an entire software product which is typically composed of one or more software packages (`pkg`))	`pkg`
4	`Name`	The name of this software package. This is a duplicate of field 2.	`glib`
5	`Version`	The version of this software entry.	`2.2`
6	`Revision`	The revision of this software entry.	`5`
7	`Desc`	A brief (single-line) description of this software entry.	`The GNU C library.`
8	`URL`	A URL associated with this software entry.	`http://www.gnu.org`
9	`License`	License information about this entry.	`The GNU GPL license applies.`
10	`Category`	A software category this entry is associated with.	`library`
11	`SubCategory`	A software sub-category this entry is associated with.	`general`
12	`OS Name`	The name of the operating system (OS) this software runs on.	`linux`
13	`OS Version`	The OS version this software runs on.	`2.4`
14	`Arch`	The CPU architecture this software runs on.	`i386`
15	`ISArch`	The instruction set architecture (platform) this software runs on. This is the more general platform of which the `Arch` is a member.	`IA32`
16	`Install Date`	The date the software was installed.	`1049489752`
17	`Build Date`	The date the software was built and packaged.	`1029489752`
18	`Production Stamp`	Some type of identifier generated by the software producer.	`porky.devel.redhat.com`
19	`Base Dir`	The base directory under which the software is installed.	`/usr/lib`
20	`Disk Usage`	The amount of disk space this software requires for installation (bytes).	`347311`
21	`Vendor Name`	The name of the vendor who produced the software.	`Red Hat, Inc.`
22	`Vendor Email`	The vendor's email address.	`[email protected]`
23	`Vendor Phone`	The vendor's phone number.	`+1-408-555-1212`
24	`Vendor Stock`	The vendor's stock/identifier for this software.	`X1234A`
25	`Master Name`	The name of the software entry to which this entry belongs. Typically this is the package's product entry.	`System Environment/Libraries`
26	`Master Version`	The master's version.	`7.2`
27	`Master Revision`	The master's revision.	`5`
28	`Desc Verbose`	A verbose description describing the product. Newlines are indicated by `\n` strings embedded in the field.	`A very\ngood general C library.`
29	`Copyright`	A copyright statement for the product. Newlines are indicated by \n strings embedded in the field.	`Copyright Red Hat Inc.\nAll rights reserved.`
30	`Next`	The name of the next software entry in the hierarchy.	`bzip2-libs`
31	`Slaves`	A comma seperated list of software entries for which this entry is the parent.	`libcutil`
32	`PkgDeps`	A comma seperated list of package names + version for which this package depends upon.	`baseos-1.1,kernel-2.4`

Information about files associated with software packages is provided when the +swfiles option is specified. The format of the output is as follows:

Table 22. Software File Information

Field # Keyword Description Example

0 software The word software specifies the usage described in this section. software

1 file The word file specifies the usage described in this section. file

2 Name The canonical name of the software package or product. glib

type

The type of file entry:

File

Directory

Hard-link

Symbolic-Link

Character-Device

Black-Device

File

4 path The pathname of the file entry. /usr/lib/libc.so

5 linkto If the entry is a symlink, this field specifies what the link points at. /usr/lib/libc.so.3

6 size The size of the file in bytes. 893100

7 md5 The MD5 checksum. abcdefawd230982434asdf

8 checksum A platform specific checksum. 100343

9 pkgnames List of all package names to which this entry belongs. glib

Table 23. Format of a software desc Entry

Field #	Keyword	Description	Example
0	`software`	The word `software` specifies the usage described in this section.	`software`
1	`desc`	The word `desc` specifies the usage described in this section.	`desc`
2	`Name`	The name of the software.	`glib`
3	`Description`	The description of the entry.	`Software Passed QA?`
4	`Value`	The value of the description.	`YES`

Class sysconf

The SysConf class provides information about general system configuration parameters. The format of this data is as follows:

Table 24. Format of a printer desc Entry

Field #	Keyword	Description	Example
0	`sysconf`	The word `sysconf` specifies the usage described in this section.	`sysconf`
1	`unused`	This field is unused.
2	`Variable`	Names the variable being described. The variable matches the valid values for `--show``variable`.	`_SC_OPEN_MAX`
3	`Description`	Description of what this variable means.	`Max open files per process`
4	`Value`	The value of this entry.	`1024`

NOTES

The --format report format is subject to additive changes. That is, the placement of existing fields will not be changed, but new fields may be added. If a field is made obsolete, it's position in the output will remain, but the content will be empty.

AUTHOR

MagniComp http://www.MagniComp.com

URL

http://www.magnicomp.com/sysinfo

FILES

/opt/sysinfo/config - Directory of config files

Name

Synopsis

DESCRIPTION

Class device

Device CpuInfo Information

Device CacheInfo Information

Device Description Information

Device NetIf Information

Class filesys

Class general

Class kernel

Class license

Class NetIf

Class Network

Class partition

Class printer

Class siteinfo

Class software

Class sysconf

NOTES

AUTHOR

URL

FILES

SEE ALSO